plastic pipe work



Sunday, 11 November 2012


Plastic pipe work




Plastic pipe work



















The common defects to plastic pipe

Impact damage during installation

The Pipes can easily break

Can crack easily due to pressure.




Materials
· Plastic pipe 15mm x 25m £70 (1)
· 90 degree pipe coupling 15mm £5 (1)
· Straight pipe coupling 15mm £5 (1)
· Equal tee fitting and inserts 15mm £10 (2)
· Plastic pipe inserts £2 (10)



The defects and limitations of

· It is very flexible

· We have different types of sizes



Tools
· Buckets
· Rench
· Dust sheets
· Screw driver (flathead)
· PVC plastic grip cutters




PPE
· Boots
· Gloves
· Goggles



Risk assessment

Sharp pipe ends may cause cuts
Cutting finger using PVC cutters

We wear correct PPE. To prevent these risks from happening. To stop cutting your fingers when like cutting they pipe keep hands away and always on handles and keep away form they blade. Then last wear gloves or fill then end of pipe so you don’t cut your self, we are working to they health and safty act of 1974.



Method statement

We first got our PPE on, and then we made way to the area of work and seen the problem. So we looked and found the main water simply, trend it off after we put a bucket under the component joint from the pipe and tock it out. We got the pipe and cut to about 50mm with a par of PVC grip cutters. Refitted back in place and testes for any leaks then finished (plus clearance).






Quote

Dear customer

We have inspected the plastic pipe work and found a split in a section of the plastic piping

We turned of the water form the pipe that was leaking and put a bucket under to stop water from going everywhere and a dustsheet to protect it from spreading over the area.

Next we had a look at the components we are needed and the way to reinstall it.

We cut a of pipe to the same size and then resouldered the fitting and then put it back in place.

Then we test to see any leaks and problems then finished and pack away (plus clearness).



Times

6 hours

Cost

The cost of all the materials and labour will cost £540

• Materials £120
• Labour £20 per hour
• Overheads (petrol,PPE,permit) £200
Total cost £540


 


No comments:



Post a Comment


Comments

Post a Comment

Popular posts from this blog

Felt And Tile Battens

Image
Felt and tile battens Felt and tile battens The common defects for felt tile battens · Rips and tiers in then felt · Batten pulling out form first fix of they roof stretcher and falling · Using they wrong felt for they type of tile your laying · Rotting of they battens Possible defects and limitations in the materials · They size of they batten and thinness · They different type of felt use on they tile you use · They lasting of they felt and its duribitly Tools • Pencil • Retractable knife • Tape • Hammer • Broom • Bin • Dust pan brush • Tri square • Panel saw • Hop up PPE • Boots • Gloves • Goggles • Hard hat • Dust mask Plant higher • Scaffolding £1,800 • Extra ladders £150 • Sk...
Read more

Replace Skirting Board

Image
Replace Skirting board   Common defects to skirting board .If the timber is exposed to high moisture content wet rod decay takes places. Wood or timber  can easily break whilst fitting . .If all ends are not well fitted together ,it can cause the skirting easily separate into many pieces .Timber or wood decay caused by insect attack ,wood boring beetles can attack wood or timber in unexposed areas  under stairs cupboards or on stairs down to basements.  Materials Skirting Board £3.00 per metre (60) Wood filler £14 (3) screws £12 (1) instant grab adhesive £9.00  (2) Decorator 's Caulk £4.00  (1) PVA wood glue £5.00  (3)   Possible defects in materials and there limitations It can be cut Knocks are missing it can be bould Tools Pencil Mitre saw or mitre box Coping saw Tape measure Hammer Air nailer Square PPE   Boots   Gloves...
Read more

Copper water pipe

Image
Copper pipe work Copper pipe work The common defects to Copper pipe work Dents to the copper pipe Splits in pipe because of it expanding from the cold Not a lot of strength in the copper pipe (poorly made) Materials Roll of lead-free solder £20 (1) Torch gas tank £40 (1) Copper piping 28mm x 3m £40 (1) Kuterlite elbow 28mm £10 (1) Yorkshire slow bend 28mm £15 (1) The defects and limitations of Copper pipe work Different type of sizes (does not match) Not flexible Tools Buckets Wrench Dust sheets Torch Screw driver (flathead) Weir ball Pipe cutter PPE Boots Gloves Goggles Risk assessment Burns from torch(hight risk) Cuts to hands(low risk) We wear correct PPE to prevent these risks from happening. To avoid cuts we wear gloves to protect our hands and lower the risk of getting any. When working with copper piping there is a risk of b...
Read more