Letter plate

Letter Plate


Letter Plate


The common defects to letter Plate

· Will rust they spring and latter plate
· Can become stiff over time
· Nuts on threaded rod will rust


Materials

· Victorian Letter Plate Brass 76x254mm £80 (1)
· Threaded Rod £10 (2)
· Nuts £5 (1 bag)




The defects and limitations of letter Plate

· Different styles of letter plates
· Different finishes of letter plates




Tools
· Pencil
· Combination square
· Cordless drill
· 10mm drill bit
· Claw hammer
· 25mm and 13mm chisel
· Jigsaw
· 110v transformer






PPE
· Boots
· Gloves
· Goggles


Risk assessment

· Cuts to hand
· Dust and wood filing getting in eye
· Using power tools

We wear correct PPE. To prevent these risks from happening. To stop cuts to hands wear gloves so any wood or splinters. Then to stop dust or wood in eye wear goggles and also it will help when using power tools because PPE will help and use must be trained to use them. we are working to they health and safety act of 1974.


Method statement

We first got our PPE on, and then we made way to the area of work and found out that your latter plate was rusty and broken, so we got they same one to you door and made way back and to stared work. So we unloosened the nuts and pulled it out and then started to put new plate in but it was a bigger plate so we chisled out about 1mm out and it fitted back nice and easy. Then put nuts back on threaded rod and then finish any last touches and pack away (plus clearness).




Quote

Dear customer

We have inspected letter plate in the door and found it has rusted and the spring had broken

We then went to go get a new latter plate form a builder’s materials shop and made way back

Then tock out old latter plate and fitted in the new one, but it was a bit bigger so we had to chisel out a bit then fix back in place.

Then tested it to see if works and then finish any last touches and pack away (plus clearness).




Times

6 hours

Cost

The coast of all they materials and labour will cost £485

• Materials £105
• Labour £30 per hour
• Overhead (petrol,PPE,permit) £200

Total cost £485

Comments

Post a Comment

Popular posts from this blog

Felt And Tile Battens

Image
Felt and tile battens Felt and tile battens The common defects for felt tile battens · Rips and tiers in then felt · Batten pulling out form first fix of they roof stretcher and falling · Using they wrong felt for they type of tile your laying · Rotting of they battens Possible defects and limitations in the materials · They size of they batten and thinness · They different type of felt use on they tile you use · They lasting of they felt and its duribitly Tools • Pencil • Retractable knife • Tape • Hammer • Broom • Bin • Dust pan brush • Tri square • Panel saw • Hop up PPE • Boots • Gloves • Goggles • Hard hat • Dust mask Plant higher • Scaffolding £1,800 • Extra ladders £150 • Sk...
Read more

Replace Skirting Board

Image
Replace Skirting board   Common defects to skirting board .If the timber is exposed to high moisture content wet rod decay takes places. Wood or timber  can easily break whilst fitting . .If all ends are not well fitted together ,it can cause the skirting easily separate into many pieces .Timber or wood decay caused by insect attack ,wood boring beetles can attack wood or timber in unexposed areas  under stairs cupboards or on stairs down to basements.  Materials Skirting Board £3.00 per metre (60) Wood filler £14 (3) screws £12 (1) instant grab adhesive £9.00  (2) Decorator 's Caulk £4.00  (1) PVA wood glue £5.00  (3)   Possible defects in materials and there limitations It can be cut Knocks are missing it can be bould Tools Pencil Mitre saw or mitre box Coping saw Tape measure Hammer Air nailer Square PPE   Boots   Gloves...
Read more

Copper water pipe

Image
Copper pipe work Copper pipe work The common defects to Copper pipe work Dents to the copper pipe Splits in pipe because of it expanding from the cold Not a lot of strength in the copper pipe (poorly made) Materials Roll of lead-free solder £20 (1) Torch gas tank £40 (1) Copper piping 28mm x 3m £40 (1) Kuterlite elbow 28mm £10 (1) Yorkshire slow bend 28mm £15 (1) The defects and limitations of Copper pipe work Different type of sizes (does not match) Not flexible Tools Buckets Wrench Dust sheets Torch Screw driver (flathead) Weir ball Pipe cutter PPE Boots Gloves Goggles Risk assessment Burns from torch(hight risk) Cuts to hands(low risk) We wear correct PPE to prevent these risks from happening. To avoid cuts we wear gloves to protect our hands and lower the risk of getting any. When working with copper piping there is a risk of b...
Read more