Rain water gutter

Rainwater goods


Rainwater goods


















The common defects to Rainwater goods



·         Ponding to guttering if not put to the right drop

·         Split gutters

·         Blockage to the outlet


Materials



·         Gutters half round 4m £30 (1)

·         Stop-End Outlet Round £10 (1)

·         Fascia Bracket Round £4 (8)

·         1 1/2" inch Round Head Screws Pack £10 (1)


The defects and limitations of Rainwater goods


·         Different types (colors,  pvc or metal ect)

·         Not flexible


Tools

·         Cordless drill

·         A small pilot whole drill bit

·         Tape

·         Pencil

·         Level

·         Hack saw

·         String line


PEE


·         Boots

·         Gloves

·         Goggles


Plant hire

·         Mobile tower



Risk assessment


·         Falling form height (high risk)

·         Objects falling from height (high risk)

·         Cuts to hands (low risk)


We wear correct PPE. To prevent these risks from happening. To stop falling from heights we can wear harnesses, helmet and put nets this will also prevent from falling objects as well. Then last for cuts on hand keep gloves on and be careful of the  area, we are working  at height regulations 2005 act and health and safety act 1974.



Method statement


 We first got our PPE on, and then we assemble the tower together to a safe and good working way of the Health and Safety Acts in place for the tower job. We got up to the gutter of roof we saw the split. We removed and then measured   the size that was 700mm and  cut the same length and fit it back in place and then tested if all is good and there are no leaks and then finished (plus clearance ). 




Quote

Dear customer


We have inspected the guttering on your roof and will have to removed a part of your gutter as it has split


We first get the same gutter part that has been used form a local materials shop that sells the same product.


Next we ripped out old part and checked it away in they din or use for smaller parts and put new part in.


Then we tested to see any leaks and problems then finished the job (plus clearance).


 Times

6 hours


Cost

They cost of all the materials, Mobile tower and labour will cost £1,002


•   Materials £82


•   Mobile tower £600

•   Labour £20 per hour

•   Overheads (petrol,PPE,permit) £200


Total cost £1,002

Comments

Post a Comment

Popular posts from this blog

Felt And Tile Battens

Image
Felt and tile battens Felt and tile battens The common defects for felt tile battens · Rips and tiers in then felt · Batten pulling out form first fix of they roof stretcher and falling · Using they wrong felt for they type of tile your laying · Rotting of they battens Possible defects and limitations in the materials · They size of they batten and thinness · They different type of felt use on they tile you use · They lasting of they felt and its duribitly Tools • Pencil • Retractable knife • Tape • Hammer • Broom • Bin • Dust pan brush • Tri square • Panel saw • Hop up PPE • Boots • Gloves • Goggles • Hard hat • Dust mask Plant higher • Scaffolding £1,800 • Extra ladders £150 • Sk...
Read more

Replace Skirting Board

Image
Replace Skirting board   Common defects to skirting board .If the timber is exposed to high moisture content wet rod decay takes places. Wood or timber  can easily break whilst fitting . .If all ends are not well fitted together ,it can cause the skirting easily separate into many pieces .Timber or wood decay caused by insect attack ,wood boring beetles can attack wood or timber in unexposed areas  under stairs cupboards or on stairs down to basements.  Materials Skirting Board £3.00 per metre (60) Wood filler £14 (3) screws £12 (1) instant grab adhesive £9.00  (2) Decorator 's Caulk £4.00  (1) PVA wood glue £5.00  (3)   Possible defects in materials and there limitations It can be cut Knocks are missing it can be bould Tools Pencil Mitre saw or mitre box Coping saw Tape measure Hammer Air nailer Square PPE   Boots   Gloves...
Read more

Copper water pipe

Image
Copper pipe work Copper pipe work The common defects to Copper pipe work Dents to the copper pipe Splits in pipe because of it expanding from the cold Not a lot of strength in the copper pipe (poorly made) Materials Roll of lead-free solder £20 (1) Torch gas tank £40 (1) Copper piping 28mm x 3m £40 (1) Kuterlite elbow 28mm £10 (1) Yorkshire slow bend 28mm £15 (1) The defects and limitations of Copper pipe work Different type of sizes (does not match) Not flexible Tools Buckets Wrench Dust sheets Torch Screw driver (flathead) Weir ball Pipe cutter PPE Boots Gloves Goggles Risk assessment Burns from torch(hight risk) Cuts to hands(low risk) We wear correct PPE to prevent these risks from happening. To avoid cuts we wear gloves to protect our hands and lower the risk of getting any. When working with copper piping there is a risk of b...
Read more