Door locks

Door locks


Door locks



















The common defects to door locks

·         The spring in they Mortice lock brakes

·         Get stiff over time

·         Poorly manufactured



Materials

·         Mortice lock Chrome 2.5in £20 (1)

·         Madrid Lock Handle £30 (1)


The defects and limitations of door locks

·         Different  types of locks

·         The type of levels on locks

·         The poor or good make of they lock



Tools

·         Pencil

·         Cordless drill

·         Machine Flat bits set

·         Crosshead screw driver

·         Bradel

·         Chisel 25mm and 13mm

·         Marking gauge


PPE

·         Boots

·         Gloves

·         Goggles


Risk assessment

·         Splinters to hand

·         Dropping tools 

·         Cuts form when chiseling

We wear correct PPE. To prevent these risks from happening. To stop splinters getting in hand wear gloves so it will not get right in when handling wood. Then to prevent cuts from chisel hold well and keep away form hands. And we boots so that if you drop a tool your feet will be safe. We are working to the health and safety act of 1974.


Method statement

We first got our PPE on, and then we made our way to the area of the door lock and saw that the lock was broken and the area around split and making the lock loose. So we tock all out and strted to mark up were it will be for the new slot for it to sit in. After its all mark and correct we started to dril holes in with a machine flat bit and then chsile to make look good and fit easly. Then after marked were the holes for they handle and key hole will be drill it out each side half way and fixed all together. So that it will cose but we have to move the door fram plat up a little so it will lock and hold in place as well. We got the plate and moved and marked it corisponding to the lock and chisled and driled a bit so it locks well. Then  finished any last touches and packed away (plus clearance).


Quote

Dear customer

We have inspected door lock and the area around is all split and loose, so will replace with a new lock and hole.

So we will mark up were it shall be, it will be half way in then center of the door and then cut the are of the lock will fit in to.

After chiseled and made it to a nice fit and then make the area for a nice flush fit and chiseled it out a little.

Then marked were handle and keyhole will be and then assembled all together and then check for any other problems and then start to finish up and pack away (plus clearance).   


 Times

6 hours


Cost

The cost of all the materials and labour will be £490

•   Materials £50

•   Labour £40 per hour

•   Overhead (petrol,PPE,permit) £200


Total cost £490













Comments

  1. Unknown16 March 2015 at 22:34

    Locks Changed A Brisbane locksmith changing locks after a break in or burglary is always a good idea if you are in doubt to weather or not the keys have been stolen.

    ReplyDelete

Post a Comment

Popular posts from this blog

Felt And Tile Battens

Image
Felt and tile battens Felt and tile battens The common defects for felt tile battens · Rips and tiers in then felt · Batten pulling out form first fix of they roof stretcher and falling · Using they wrong felt for they type of tile your laying · Rotting of they battens Possible defects and limitations in the materials · They size of they batten and thinness · They different type of felt use on they tile you use · They lasting of they felt and its duribitly Tools • Pencil • Retractable knife • Tape • Hammer • Broom • Bin • Dust pan brush • Tri square • Panel saw • Hop up PPE • Boots • Gloves • Goggles • Hard hat • Dust mask Plant higher • Scaffolding £1,800 • Extra ladders £150 • Sk...
Read more

Replace Skirting Board

Image
Replace Skirting board   Common defects to skirting board .If the timber is exposed to high moisture content wet rod decay takes places. Wood or timber  can easily break whilst fitting . .If all ends are not well fitted together ,it can cause the skirting easily separate into many pieces .Timber or wood decay caused by insect attack ,wood boring beetles can attack wood or timber in unexposed areas  under stairs cupboards or on stairs down to basements.  Materials Skirting Board £3.00 per metre (60) Wood filler £14 (3) screws £12 (1) instant grab adhesive £9.00  (2) Decorator 's Caulk £4.00  (1) PVA wood glue £5.00  (3)   Possible defects in materials and there limitations It can be cut Knocks are missing it can be bould Tools Pencil Mitre saw or mitre box Coping saw Tape measure Hammer Air nailer Square PPE   Boots   Gloves...
Read more

Copper water pipe

Image
Copper pipe work Copper pipe work The common defects to Copper pipe work Dents to the copper pipe Splits in pipe because of it expanding from the cold Not a lot of strength in the copper pipe (poorly made) Materials Roll of lead-free solder £20 (1) Torch gas tank £40 (1) Copper piping 28mm x 3m £40 (1) Kuterlite elbow 28mm £10 (1) Yorkshire slow bend 28mm £15 (1) The defects and limitations of Copper pipe work Different type of sizes (does not match) Not flexible Tools Buckets Wrench Dust sheets Torch Screw driver (flathead) Weir ball Pipe cutter PPE Boots Gloves Goggles Risk assessment Burns from torch(hight risk) Cuts to hands(low risk) We wear correct PPE to prevent these risks from happening. To avoid cuts we wear gloves to protect our hands and lower the risk of getting any. When working with copper piping there is a risk of b...
Read more