Garden Gate


Garden Gates

Garden Gates






The common defects to gates
·        Wood splitting
·        Hinges coming louse
·        Nails in the wood getting nail fatigue.


Materials
·        Studwork Timber 38x89mmx2.4m  £ £15 (1)
·        Kiln Dried Treated Regular 45x120mmx2.4m £ £15 (1)
·        Galvanized Nails 2inchs £20 (1 bag)
·        Garden Gate Kit Galvanized £ 20 (1)



The defects and limitations of gates
·        They are different sizes of garden gates
·        They are many different finishes





Tools

•   Dust pan and brush
•   Broom
•   Cordless drill
•   Pencil
•   Tap
•   Drill bits
•   Combinations Square
•   Panel saw
•   Chop saw

PPE   

·        Boots
·        Gloves
·        Goggles

Risk assessment
•      Cuts to hands
•      Splinters
•      Power tools

We wear correct PPE. To prevent these risks from happening. To stop cuts to hands wear gloves sothat  any wood or splinters. Then to stop dust or wood in eyes wear goggles and also it will help when using power tools because PPE will help and use must be trained to use them. We are working to the health and safety act of 1974.






Method statement

We first got our PPE on, and then we made way to the area of work and found out the facing of gate is split all they way down they middle of some of them. So we then went to go and get the same existing facing and made way back. Then start tacking it off form gate and then measured out the length to they new facing its about 400mm and the just put back in same position and spacing. After fixed all well and made any last touches and pack away  (plus clearness).






Quote

Dear customer

We have inspected your gate when making way to house and found it has a few big major splits down the face of wood.

So we got a few of the same wood gate facings and made way back to work area so that we can start to replace it all.

Ripped of existing facing and then made any slight ejectments to new facings (cutting off parts top fit).

 Then put were existing old facing and then made any last touches finished and pack away (plus clearness). 



 Times

6 hours


Cost

They cost t of all the materials and labour  £450

•   Materials £70
•   Labour £30 per hour
•   Overhead (petrol,PPE,permit) £200


Total cost £450

Comments

Post a Comment

Popular posts from this blog

Felt And Tile Battens

Image
Felt and tile battens Felt and tile battens The common defects for felt tile battens · Rips and tiers in then felt · Batten pulling out form first fix of they roof stretcher and falling · Using they wrong felt for they type of tile your laying · Rotting of they battens Possible defects and limitations in the materials · They size of they batten and thinness · They different type of felt use on they tile you use · They lasting of they felt and its duribitly Tools • Pencil • Retractable knife • Tape • Hammer • Broom • Bin • Dust pan brush • Tri square • Panel saw • Hop up PPE • Boots • Gloves • Goggles • Hard hat • Dust mask Plant higher • Scaffolding £1,800 • Extra ladders £150 • Sk...
Read more

Replace Skirting Board

Image
Replace Skirting board   Common defects to skirting board .If the timber is exposed to high moisture content wet rod decay takes places. Wood or timber  can easily break whilst fitting . .If all ends are not well fitted together ,it can cause the skirting easily separate into many pieces .Timber or wood decay caused by insect attack ,wood boring beetles can attack wood or timber in unexposed areas  under stairs cupboards or on stairs down to basements.  Materials Skirting Board £3.00 per metre (60) Wood filler £14 (3) screws £12 (1) instant grab adhesive £9.00  (2) Decorator 's Caulk £4.00  (1) PVA wood glue £5.00  (3)   Possible defects in materials and there limitations It can be cut Knocks are missing it can be bould Tools Pencil Mitre saw or mitre box Coping saw Tape measure Hammer Air nailer Square PPE   Boots   Gloves...
Read more

Copper water pipe

Image
Copper pipe work Copper pipe work The common defects to Copper pipe work Dents to the copper pipe Splits in pipe because of it expanding from the cold Not a lot of strength in the copper pipe (poorly made) Materials Roll of lead-free solder £20 (1) Torch gas tank £40 (1) Copper piping 28mm x 3m £40 (1) Kuterlite elbow 28mm £10 (1) Yorkshire slow bend 28mm £15 (1) The defects and limitations of Copper pipe work Different type of sizes (does not match) Not flexible Tools Buckets Wrench Dust sheets Torch Screw driver (flathead) Weir ball Pipe cutter PPE Boots Gloves Goggles Risk assessment Burns from torch(hight risk) Cuts to hands(low risk) We wear correct PPE to prevent these risks from happening. To avoid cuts we wear gloves to protect our hands and lower the risk of getting any. When working with copper piping there is a risk of b...
Read more