HAND Basin


Friday, 26 October 2012


Hand basin



Hand basin



























The common defects to Hand basin

· Can easily be cracked
· Falling off the wall
· Overflow of water when to much pressure is applied to the drainage hole






Materials

· Basic hand basin £ 70 (1)
· Basin taps £20 (2)
· Fischer Basin Fixing Kit £10 (1)






The defects and limitations of Hand basin

· Different type of sizes and colors of hand basins
· Different type of taps and sizes



Tools

· Wrench
· Dust sheets
· Justibal spinier
· Screw diver (flathead)
· Cordless drill
· Drill bit
· Level
· Pencil
· Tape
· Tap spanner



PPE
· Boots
· Gloves
· Goggles



Risk assessment

· Falling objects (high risk)
· Sharp objects(medium risk)
· Injury to feet(low risk
)· Shared of dirt or hand basin getting in eye(medium risk)

We wear correct PPE. To prevent these risks from happening. To stop objects from falling we keep our hand dry when picking up hand basin. Also wear gloves to stop any sharp objects from cutting our hands. Wear boots to prevent any injuries which might occur if the basin falls. As well you must wear goggles when drilling the hole for where the basin will be and in case the person shatters the basin brakes.



Method statement

We first got our PPE on. Then started to work out the area of where the basin will be and marked, plumb and level on the wall. We started to assemble the basin together with the tap on before attaching to wall, then offer it up too the marked wall measurements and screwed it to the wall to give a fame fixing .After we attached all pipes and then we finished (plus clearance ).



Quote

Dear customer

We have inspected the area were you would like the hand basin to be installed.

We marked up the area on the wall with a tape and leveled to get plumb lines and leveled through out.

Next we drilled the holes where the hand basin is going to sit ,we attached the tapes to the hand basin.

We offered hand basin up the wall and we used Fischer basin fixing kit and we attached the basin to the wastage pipes and water flow pipes .

Then we test to see any leaks and problems then finished and pack away (plus clearness).



Times

6 hours

Cost

They cost of all they materials and labour will cost £440

• Materials £120
• Labour £20 per hour
• Overhead (petrol,PPE,permit) £200

Total cost £440

Comments

Post a Comment

Popular posts from this blog

Felt And Tile Battens

Image
Felt and tile battens Felt and tile battens The common defects for felt tile battens · Rips and tiers in then felt · Batten pulling out form first fix of they roof stretcher and falling · Using they wrong felt for they type of tile your laying · Rotting of they battens Possible defects and limitations in the materials · They size of they batten and thinness · They different type of felt use on they tile you use · They lasting of they felt and its duribitly Tools • Pencil • Retractable knife • Tape • Hammer • Broom • Bin • Dust pan brush • Tri square • Panel saw • Hop up PPE • Boots • Gloves • Goggles • Hard hat • Dust mask Plant higher • Scaffolding £1,800 • Extra ladders £150 • Sk...
Read more

Replace Skirting Board

Image
Replace Skirting board   Common defects to skirting board .If the timber is exposed to high moisture content wet rod decay takes places. Wood or timber  can easily break whilst fitting . .If all ends are not well fitted together ,it can cause the skirting easily separate into many pieces .Timber or wood decay caused by insect attack ,wood boring beetles can attack wood or timber in unexposed areas  under stairs cupboards or on stairs down to basements.  Materials Skirting Board £3.00 per metre (60) Wood filler £14 (3) screws £12 (1) instant grab adhesive £9.00  (2) Decorator 's Caulk £4.00  (1) PVA wood glue £5.00  (3)   Possible defects in materials and there limitations It can be cut Knocks are missing it can be bould Tools Pencil Mitre saw or mitre box Coping saw Tape measure Hammer Air nailer Square PPE   Boots   Gloves...
Read more

Copper water pipe

Image
Copper pipe work Copper pipe work The common defects to Copper pipe work Dents to the copper pipe Splits in pipe because of it expanding from the cold Not a lot of strength in the copper pipe (poorly made) Materials Roll of lead-free solder £20 (1) Torch gas tank £40 (1) Copper piping 28mm x 3m £40 (1) Kuterlite elbow 28mm £10 (1) Yorkshire slow bend 28mm £15 (1) The defects and limitations of Copper pipe work Different type of sizes (does not match) Not flexible Tools Buckets Wrench Dust sheets Torch Screw driver (flathead) Weir ball Pipe cutter PPE Boots Gloves Goggles Risk assessment Burns from torch(hight risk) Cuts to hands(low risk) We wear correct PPE to prevent these risks from happening. To avoid cuts we wear gloves to protect our hands and lower the risk of getting any. When working with copper piping there is a risk of b...
Read more