Plastic Waste system

Plastic waste system


Plastic waste system






















The common defects to Plastic waste system

·         Blocking in the pipe

·         High water pressure in they pipes

·         Splits in the pipe

·         They can’t be put in a high pressured area




Materials

·         Plastic waste pipes 32mmx2m £15 (1)

·         Trap £20 (1)

·         Plastic pipe connector 32mm £5 (2)

·         Compression 90Deg Knuckle Bend 32mmn £5 (1)





The defects and limitations of Plastic waste system



·         Different type of sizes

·         Not flexible

·         Bent out of shape



Tools

·         Buckets

·         Wrench

·         Dust sheets

·         Screw driver (flathead)

·         Hack saw




PPE

·         Boots

·         Gloves

·         Goggles



Risk assessment


·         Wet floors and areas (high risk)

·         End of pipe still sharp(low risk)

·         Trips (medium risk)

 We wear correct PPE. To prevent these risks from happening. To stop use from getting hart or tripping over objects keep a tidy area at all times, remove pipe form walk ways and work areas. We wear gloves or hardhat when working with pipe and overhead pipe work. Lay dust sheets to stop water getting everywhere and also buckets as well.





Method statement

We first got our PPE on. We look around to find the split, leaks and damaged piping, when we spot the area we top water mains and we removed damaged area with a bucket under it. We got rid of the damaged pipe we then took the measurements of the damaged area that was 300 mm and fixed back into place with new joint connectors, we then tested for any leaks and other problems then finished (plus clearance).  


Quote

Dear customer


We have inspected the plastic waste and you had a split in the pipe and trap  was not tight.


We turn  of the water so that no more water can get out the  tap and then put a dust sheet and bucket under the pipe needs coming out to collect the water.


Next we cut a pipe to size of existing length and re attached to the same place.


We then tightened the trap back up.


Then we test to see any leaks and problems then finished and then we packed  (plus clearness).



 Times


6 hours


Cost


They coast of all they materials and labour will cost £370.


•   Materials £50

•   Labour £20 per hour

•   Overhead (petrol,PPE,permit) £200

Total cost £370

Comments

Post a Comment

Popular posts from this blog

Felt And Tile Battens

Image
Felt and tile battens Felt and tile battens The common defects for felt tile battens · Rips and tiers in then felt · Batten pulling out form first fix of they roof stretcher and falling · Using they wrong felt for they type of tile your laying · Rotting of they battens Possible defects and limitations in the materials · They size of they batten and thinness · They different type of felt use on they tile you use · They lasting of they felt and its duribitly Tools • Pencil • Retractable knife • Tape • Hammer • Broom • Bin • Dust pan brush • Tri square • Panel saw • Hop up PPE • Boots • Gloves • Goggles • Hard hat • Dust mask Plant higher • Scaffolding £1,800 • Extra ladders £150 • Sk...
Read more

Replace Skirting Board

Image
Replace Skirting board   Common defects to skirting board .If the timber is exposed to high moisture content wet rod decay takes places. Wood or timber  can easily break whilst fitting . .If all ends are not well fitted together ,it can cause the skirting easily separate into many pieces .Timber or wood decay caused by insect attack ,wood boring beetles can attack wood or timber in unexposed areas  under stairs cupboards or on stairs down to basements.  Materials Skirting Board £3.00 per metre (60) Wood filler £14 (3) screws £12 (1) instant grab adhesive £9.00  (2) Decorator 's Caulk £4.00  (1) PVA wood glue £5.00  (3)   Possible defects in materials and there limitations It can be cut Knocks are missing it can be bould Tools Pencil Mitre saw or mitre box Coping saw Tape measure Hammer Air nailer Square PPE   Boots   Gloves...
Read more

Copper water pipe

Image
Copper pipe work Copper pipe work The common defects to Copper pipe work Dents to the copper pipe Splits in pipe because of it expanding from the cold Not a lot of strength in the copper pipe (poorly made) Materials Roll of lead-free solder £20 (1) Torch gas tank £40 (1) Copper piping 28mm x 3m £40 (1) Kuterlite elbow 28mm £10 (1) Yorkshire slow bend 28mm £15 (1) The defects and limitations of Copper pipe work Different type of sizes (does not match) Not flexible Tools Buckets Wrench Dust sheets Torch Screw driver (flathead) Weir ball Pipe cutter PPE Boots Gloves Goggles Risk assessment Burns from torch(hight risk) Cuts to hands(low risk) We wear correct PPE to prevent these risks from happening. To avoid cuts we wear gloves to protect our hands and lower the risk of getting any. When working with copper piping there is a risk of b...
Read more