Replacement Of Inspection Cover



Monday, 17 September 2012


Replacement of inspection cover


Replacement of inspection cover






















The common Defects of inspection covers

· Inspections covers copulas in on you because of they lasting of they man hole we it is about to lost its duribitly

· Can come loses and fall off
So it shall be knocked off or come lose and be open for any one to full in
· Damage to they top of cover and frame
Making it less strong and easy for it to fall in to


Materials

· Shaper sand £5.00
· Cement £7.00
· Steel manhole cover £40
· Water

Limitations of inspection covers

· Different type, weight and size
Making it more difficult to install and knowing what one is used for

· Covers and frame
They type of frame is made form different metals so they have different lasting ability


· Lasting for they manhole
They time length of they manhole were it has to be replaced



Tools

· Bluster
· Lump hammer
· Dust pan brush
· Bin
· Manhole keys
· Bucket
· Pointing trowel
· Brick trowel
· Level



PPE

· Boots

· Gloves

· Goggles

· Dust mask

Risk assessment

· Mortar mix going in eye

· Manhole cover falling on foot

· Mortar going in to an open wound
We will wear the correct PPE to prevent wear goggles to stop mortar mix getting in eyes and then to wear boots that will stop your feet getting crushed form dropping a heavy manhole and cover any wounds so that it cant get in then we will be working to the (HSE) standers and they health and safety 1974 act.




Method stament
We shall put on our correct PPE on before we start the install inspection cover to be well protected. Will tack they existing man hole cover and get rid of it then we will brush lose mortar and dust so we can start to lay a fresh mix of mortar to install a new man hole cover. Then we start to mix sharp sands and cermente together to create the mortar mix then we apply that to the existing man hole cover brick wall and placed the frame and levelled it. Apply around the frame to give it a strong hold and to give it a nice finish by keeping it all flushed, after we shall clean up and do any last minute touches.

Quote
Dear customer
We have inspected your man hole and it needs a new cover, on the top
We will get rid of the existing cover and get rid of it and replace it with a new one
Then apply mortar mix to existing place of were they frame was and level
Then we will finish the last touches that need to ne done ( plus clearance)
Time
6 hours
Cost
The costs of all materials and job will cost £612 plus VAT


  • Materials £52
  • lader £20 per hr
  • overhead (petrol, PPE,permit) £200
Total cost £612



Comments

Post a Comment

Popular posts from this blog

Felt And Tile Battens

Image
Felt and tile battens Felt and tile battens The common defects for felt tile battens · Rips and tiers in then felt · Batten pulling out form first fix of they roof stretcher and falling · Using they wrong felt for they type of tile your laying · Rotting of they battens Possible defects and limitations in the materials · They size of they batten and thinness · They different type of felt use on they tile you use · They lasting of they felt and its duribitly Tools • Pencil • Retractable knife • Tape • Hammer • Broom • Bin • Dust pan brush • Tri square • Panel saw • Hop up PPE • Boots • Gloves • Goggles • Hard hat • Dust mask Plant higher • Scaffolding £1,800 • Extra ladders £150 • Sk...
Read more

Replace Skirting Board

Image
Replace Skirting board   Common defects to skirting board .If the timber is exposed to high moisture content wet rod decay takes places. Wood or timber  can easily break whilst fitting . .If all ends are not well fitted together ,it can cause the skirting easily separate into many pieces .Timber or wood decay caused by insect attack ,wood boring beetles can attack wood or timber in unexposed areas  under stairs cupboards or on stairs down to basements.  Materials Skirting Board £3.00 per metre (60) Wood filler £14 (3) screws £12 (1) instant grab adhesive £9.00  (2) Decorator 's Caulk £4.00  (1) PVA wood glue £5.00  (3)   Possible defects in materials and there limitations It can be cut Knocks are missing it can be bould Tools Pencil Mitre saw or mitre box Coping saw Tape measure Hammer Air nailer Square PPE   Boots   Gloves...
Read more

Copper water pipe

Image
Copper pipe work Copper pipe work The common defects to Copper pipe work Dents to the copper pipe Splits in pipe because of it expanding from the cold Not a lot of strength in the copper pipe (poorly made) Materials Roll of lead-free solder £20 (1) Torch gas tank £40 (1) Copper piping 28mm x 3m £40 (1) Kuterlite elbow 28mm £10 (1) Yorkshire slow bend 28mm £15 (1) The defects and limitations of Copper pipe work Different type of sizes (does not match) Not flexible Tools Buckets Wrench Dust sheets Torch Screw driver (flathead) Weir ball Pipe cutter PPE Boots Gloves Goggles Risk assessment Burns from torch(hight risk) Cuts to hands(low risk) We wear correct PPE to prevent these risks from happening. To avoid cuts we wear gloves to protect our hands and lower the risk of getting any. When working with copper piping there is a risk of b...
Read more