Hip and ridge tiles





Hip and ridge tiles


























The common defects for hip and ridge tiles
• Loose tiles
• Rusty nails
  Broken tiles.
• Moss or other substances that can block the gutters leading to overflows/ damaged gutters.


Possible defects and limitations in the materials

· They different type of stile of hip and ridge tiles
· They lasting of the tile and its durability



Tools


• Pencil
• Tape
• Hammer
• Broom
• Bin
• Dust pan brush
• Tile cutter





PPE

• Boots
• Gloves
• Goggles
• Hard hat
• Dust mask

Plant higher

• Tower £1,000
• Extra ladders £150
• Skip £195

Materials

• Galvanised nails £40 per bag (3 bags)
• Concrete Ridge 450mm £10 per length (2)
• Hip tile £5 per tile (20)
The Risk Assessment

The risk of reaping cement roofing

• Falling from height
• Slips
• Falling objects

Everybody has to wear correct ppe. We put up netting to stop falls and objects from falling and put the first set of scaffolding boards to a floor to protect the general public. Will be working to the working at height regulations 2005, (HSE) and they health and safety act of 1974.




Method statement

Before we start on your roof to reaper they hip tiles and ridge we put on they correct PPE and we shall do they job to they regulations of working at height 2005 and (HSE) as well and they health and safety act of 1974. now we will start up a tower and move to then area of were you need hip tiles replaced and ridge then find old and damaged hip and ridge tiles and skip then and replace with new hip and ridge tile after that is done and we checked the work and we will finish the last touches that need to be done plus clearance.


Quote

Dear Customer


We have inspected your roof and you need new hip and ridge tiles because they are broken and lose

Next we will get the scaffolding up to get accesses to roof more easily and got a skip

Strip all lose hip and ridge tiles and damaged ones as well

We then replace them with new ones and get rid of old and broken tiles

Then we will finish the last touches that need to be done. (plus clearance)

Times

1 days 8hrs

Cost
The costs of all the materials plus the Tower, Skip and job will cost £3,675 plus VAT.

• Tower£1,000
• Skip £195
• Ladders £150
• Materials £370
• Lader £20 per hour
Overhead (petrol,PPE,permit) £200

total cost £3,675
• 

Comments

Post a Comment

Popular posts from this blog

Felt And Tile Battens

Image
Felt and tile battens Felt and tile battens The common defects for felt tile battens · Rips and tiers in then felt · Batten pulling out form first fix of they roof stretcher and falling · Using they wrong felt for they type of tile your laying · Rotting of they battens Possible defects and limitations in the materials · They size of they batten and thinness · They different type of felt use on they tile you use · They lasting of they felt and its duribitly Tools • Pencil • Retractable knife • Tape • Hammer • Broom • Bin • Dust pan brush • Tri square • Panel saw • Hop up PPE • Boots • Gloves • Goggles • Hard hat • Dust mask Plant higher • Scaffolding £1,800 • Extra ladders £150 • Sk...
Read more

Replace Skirting Board

Image
Replace Skirting board   Common defects to skirting board .If the timber is exposed to high moisture content wet rod decay takes places. Wood or timber  can easily break whilst fitting . .If all ends are not well fitted together ,it can cause the skirting easily separate into many pieces .Timber or wood decay caused by insect attack ,wood boring beetles can attack wood or timber in unexposed areas  under stairs cupboards or on stairs down to basements.  Materials Skirting Board £3.00 per metre (60) Wood filler £14 (3) screws £12 (1) instant grab adhesive £9.00  (2) Decorator 's Caulk £4.00  (1) PVA wood glue £5.00  (3)   Possible defects in materials and there limitations It can be cut Knocks are missing it can be bould Tools Pencil Mitre saw or mitre box Coping saw Tape measure Hammer Air nailer Square PPE   Boots   Gloves...
Read more

Copper water pipe

Image
Copper pipe work Copper pipe work The common defects to Copper pipe work Dents to the copper pipe Splits in pipe because of it expanding from the cold Not a lot of strength in the copper pipe (poorly made) Materials Roll of lead-free solder £20 (1) Torch gas tank £40 (1) Copper piping 28mm x 3m £40 (1) Kuterlite elbow 28mm £10 (1) Yorkshire slow bend 28mm £15 (1) The defects and limitations of Copper pipe work Different type of sizes (does not match) Not flexible Tools Buckets Wrench Dust sheets Torch Screw driver (flathead) Weir ball Pipe cutter PPE Boots Gloves Goggles Risk assessment Burns from torch(hight risk) Cuts to hands(low risk) We wear correct PPE to prevent these risks from happening. To avoid cuts we wear gloves to protect our hands and lower the risk of getting any. When working with copper piping there is a risk of b...
Read more